Full-colour direct-to-film (DTF) heat transfers, digitally printed and cut ready to press. Seventeen sizes from 2 × 2 in to 12 × 22 in, no minimum order, and unlimited colours per design. Hot peel, soft hand, no glue lines.

Loading the configurator…

Description

What Is a Full-Colour DTF Heat Transfer?

A full-colour DTF heat transfer is a single-layer garment decoration printed entirely by digital inkjet, then bonded to a film and cut to the exact outline of your artwork. Advanced Transfers DTF heat transfers are printed this way, so one artwork file produces every colour in the design at once: there is no screen separation, no colour limit, and no weeding step to remove the background after pressing.

The practical result is a soft hand. Because the ink sits under a flexible white base rather than on top of a thick film, there is no hard edge to feel and no glue line around the border of the print. These transfers peel hot and press in twelve to fifteen seconds, which makes them a fast production option for short runs, name-and-number uniforms, print-on-demand orders and sample runs before a larger launch.

Which Sizes Can You Order?

Seventeen finished sizes are available, from 2 × 2 in for a small chest print up to 12 × 22 in for a full front or back panel. Every size is available at every quantity, so the same artwork can be produced as a single sample and then repeated at volume without re-setting the file. Sizes are sold as a finished cut size, not as a sheet: you order the rectangle your design needs and nothing is trimmed off afterwards.

Finished size (in) Finished size (in) Finished size (in) Finished size (in)
2 × 2 4 × 4 9 × 9 11 × 14
4 × 2 5 × 5 9 × 11 12 × 17
3 × 3 6 × 6 10 × 10 12 × 22
5 × 3 7 × 7 11 × 11  
  8 × 8    
11 × 5      

What Fabrics and Garments Can You Print?

Full-colour DTF heat transfers are designed for cotton, polycotton blends, fleece, light denim, lycra, nylon, elastane and non-sublimated polyester. That covers the garments most often decorated in short runs: tees, hoodies and fleece, stretchy athleisure, and cotton tote bags.

Two limits are worth stating plainly. First, this transfer is not designed for fabrics with waterproof coatings, or for sublimated or patterned polyester, or for dark denim where the dye could migrate through the print. On a fabric where you are unsure whether the dye will bleed, a blocking transfer is the safer choice. Second, headwear works only where the design does not cross a seam, for example the front panels of a five panel cap. Printing across a cap seam needs a headwear-specific transfer.

How Durable Is the Print?

Independent third-party testing puts this transfer through 70 wash cycles on the AATCC TS-008 protocol with a colour change rating of 4.5 out of 5 and no cracking and no peeling; the test report is Intertek USA00057485-REV1, dated March 2024. The inks and adhesives are water-based, phthalate-free and lead-free, and the transfer carries OEKO-TEX Standard 100 Class I certification, certificate 22.HUS.99567, valid through 31 March 2027. Lead content is under 10 ppm, and the product has passed CPSIA and California Prop 65 testing.

How Do You Apply a DTF Heat Transfer?

Press at 280 °F to 320 °F for twelve to fifteen seconds at 40 psi firm pressure, then peel hot. On a manual press, move to a higher pressure setting. This is a professional-grade transfer: it needs an air-operated or manual heat press, not a domestic iron and not a low-pressure craft press. The full step-by-step method, including precautions and aftercare, is on the Application tab.

How Do Quantities and Pricing Work?

There is no minimum order. One piece is a complete order, which is what makes this format usable for a single sample or a one-off name-and-number uniform run. Unit pricing steps down as quantity rises, with breaks at 10, 50 and 100 pieces, so a short run stays economical while a larger run gets cheaper per garment. Price per piece is shown live in the configurator as you choose a size and quantity.

What Artwork Do You Need to Supply?

Supply one artwork file in PDF, ideally exported from vector design software. Convert all fonts to outlines or shapes before uploading, and keep free-floating line weights at 0.6 pt (0.2 mm) or heavier so fine detail survives the press. Vector formats such as PDF, AI, CDR and SVG are preferred; other common formats are accepted. Transfers arrive cut and ready to press, with no weeding required.

Where This Transfer Is Not the Right Choice

Full-colour DTF is the right format for full-colour artwork in short runs, but it is not the best option in three situations. If you need an exact Pantone colour match, this transfer will be close but not exact; a screen-printed wearable transfer matches Pantone. If you need to print across a cap seam, a headwear transfer is built for that. If you are printing on coated, sublimated or patterned fabric where dye can migrate, a blocking transfer prevents bleed-through. For runs above about twenty pieces, a wearable transfer is usually the more economical route.

FAQ

Frequently Asked Questions About Full-Colour DTF Heat Transfers

What is a DTF heat transfer?

A DTF (direct-to-film) heat transfer is a full-colour garment decoration printed with digital inkjet onto a film, then bonded to a flexible white base and cut to your artwork. One file produces every colour, and there is no screen separation or weeding step.

What makes DTF different from vinyl or screen-printed transfers?

DTF prints any number of colours in one design and peels hot in a single step, so there is no weeding. The print has a soft hand with no glue line around the edge, which is the usual complaint with cut vinyl. Vinyl has no white underbase, so it cannot be printed on dark garments the same way; screen-printed transfers match Pantone exactly but are set per colour and suit longer runs.

How large can one transfer be?

Seventeen finished sizes are available, from 2 × 2 in up to 12 × 22 in. Each size is the finished cut size, so nothing is trimmed after production. The largest size at 12 × 22 in covers a full front or back panel.

Is there a minimum order?

No. A single piece is a complete order, which is what makes this format practical for a sample, a proof, or a one-off uniform run.

What quantities can I order?

Any quantity from one piece upward. Unit pricing steps down at 10, 50 and 100 pieces, so short runs stay economical and longer runs get cheaper per garment.

Which fabrics and garments can I use this transfer on?

Cotton, polycotton blends, fleece, light denim, lycra, nylon, elastane and non-sublimated polyester. In practice that means tees, hoodies, stretchy athleisure wear and cotton tote bags.

Which fabrics should I avoid?

Do not use this transfer on fabrics with waterproof coatings, on sublimated or patterned polyester, or on dark denim where the dye could migrate through the print. On any fabric you are unsure about, a blocking transfer prevents dye migration.

Can I print on a hat or cap?

Yes, on headwear that has no seam running under the design, such as the front panels of a five panel cap. If the design crosses a seam or covers mesh, use a headwear-specific transfer instead, which is designed not to crack across those features.

Can this transfer match a Pantone colour?

No. The colours are close, but they are not an exact Pantone match, and metallics are not available on this transfer. If an exact Pantone match is required, a screen-printed wearable transfer is the right product.

What temperature, time and pressure do I press at?

280 °F to 320 °F, for twelve to fifteen seconds, at 40 psi firm pressure. Use a higher pressure setting on a manual press, and peel hot. The full method is on the Application tab.

What kind of heat press do I need?

An air-operated or manual heat press. This is a professional-grade transfer and is not designed for a domestic iron, a low-pressure craft press, or any press without adequate pressure settings.

How long does the print last?

Independent third-party testing ran this transfer through 70 wash cycles on the AATCC TS-008 protocol, with a colour change rating of 4.5 out of 5 and no cracking or peeling (Intertek report USA00057485-REV1, March 2024). In everyday use that is normally longer than the life of the garment itself.

Is the ink safe?

The inks and adhesives are water-based, phthalate-free and lead-free, with lead content under 10 ppm. The transfer carries OEKO-TEX Standard 100 Class I certification (certificate 22.HUS.99567, valid through 31 March 2027) and has passed CPSIA and California Prop 65 testing.

How should I care for a printed garment?

Follow the care label on the garment itself. Wash inside out where the label allows, and avoid fabric softener on the printed area, which can coat the print and dull it over time.

What artwork file do I need to upload?

One file, in PDF, ideally exported from vector design software. Convert all fonts to outlines or shapes, and keep free-floating line weights at 0.6 pt (0.2 mm) or heavier. Vector formats such as PDF, AI, CDR and SVG are preferred; other common formats are accepted.

Do I need to weed or trim the transfer?

No. Transfers arrive cut to the outline of your artwork and ready to press. The only physical step at your end is placing, pressing and hot-peeling.

When should I choose a different transfer type?

Choose a screen-printed wearable transfer for an exact Pantone match or for runs above about twenty pieces, a headwear transfer for designs that cross a cap seam or cover mesh, and a blocking transfer for coated, sublimated or patterned fabric where dye could migrate.

Is there a setup fee or hidden charge?

There is no setup fee and no hidden charge on the product. Shipping is calculated separately at checkout.

Application

How to Apply Full-Colour DTF Heat Transfers

These transfers are pressed with an air-operated or manual heat press at 280 °F to 320 °F, held for twelve to fifteen seconds at 40 psi firm pressure, then peeled hot. The settings below are the verified settings for this product. Test on a sample garment before you run production.

Verified Press Settings

Setting Value
Press temperature 280 °F to 320 °F
Press time 12 to 15 seconds
Pressure 40 psi / firm (use a higher setting on a manual press)
Peel method Hot peel
Press type Air-operated or manual heat press

Pressing Steps

  1. Prepare the garment. Press the garment blank first, inside out, to remove wrinkles and any surface moisture. Wrinkles under the transfer are the most common cause of lifting.
  2. Place the transfer. Position the transfer printed side up on the garment, on top of the fabric and not over a seam. The finished size of the transfer is the finished size of the print, so leave the design where you want it to land.
  3. Close the press. Set the platen to 280 °F to 320 °F and close the press with firm pressure at 40 psi. On a manual press, use a higher pressure setting.
  4. Hold. Hold the press closed for twelve to fifteen seconds. Do not shorten the dwell: the adhesive needs the full heat and time to bond into the fabric.
  5. Peel hot. Open the press and peel the carrier film away immediately while the print is still warm. A slow, steady peel at roughly a 180-degree angle removes the film without lifting the graphic.
  6. Check the result. Once the film is off, the print is set. Confirm the edges are fully bonded before continuing with the rest of the run.

Care After Pressing

The print is fully bonded as soon as the carrier film is peeled, so you can continue pressing the rest of the order immediately. Follow the care label on the garment for washing. Wash inside out where the label allows, and avoid fabric softener on the printed area, which coats the print and can dull it over time. Avoid bleaching and dry cleaning unless the garment’s care label already allows them.

Precautions

  • Use an air-operated or manual heat press. This transfer is not designed for a domestic iron, a low-pressure craft press, or any press without adequate pressure settings.
  • Do not press on coated, waterproof, sublimated or patterned fabric, or on dark denim where the dye can migrate through the print. Use a blocking transfer on those fabrics.
  • Do not press a headwear design across a seam or over mesh. Use a headwear-specific transfer for those placements.
  • Keep the press platen clean. A dirty or scorched platen transfers marks onto the carrier film and onto the print.
  • Never re-press an area that has already been peeled. The adhesive will not re-bond, and the second press will either not stick or will damage the print.
  • Do not cut into or trim the finished print. Transfers are supplied cut to the artwork outline.

Test Before Production

Press one sample before running a full order, especially when you are changing fabric, garment construction or press settings. Full-colour DTF heat transfers are produced to the settings above, but every fabric reacts differently to heat and pressure, and a sample confirms that your press reaches the stated temperature, that the dwell time suits your fabric, and that the adhesive bonds cleanly. If the supplier publishes no further guidance for your specific fabric, treat the settings above as the verified baseline and adjust from a test rather than from assumption.

Shopping Cart
Scroll to Top